How to Recover Damaged SSD without Losing Data

How to Recover Damaged SSD without Losing Data

By: marysmith

SSD (Solid State Drive) storage units are used as an alternative to HDD hard drives, since they store files on microchips with interconnected flash memories, which are not volatile so they keep the information stored when the disk is disconnect. In addition, they have an integrated processor, which controls data reading and writing operations; as a plus, by not relying on a rotating physical component, you get a quiet and efficient drive.

However, despite their efficiency, they are susceptible to some damage that puts stored information at risk. So, if you have already suffered the damage of your SSD and you are looking for how to recover your information, or you want to know the signs that indicate that your SSD is about to fail to back up your data, and looking for SSD data recovery service, let’s join us to read.

Signs that the SSD is Damaged

The Blocks are Defective

SSDs have many memory cells, which replace the ones that are unusable; but, in the event that damaged blocks appear, it is an indicator that these additional cells have been used up and that it is time to change the storage unit for another.

Writing and Reading Errors

These errors occur due to the accumulation of bad blocks in the SSD, access to which is denied by the controller. This is a serious problem since it does not allow you to access the information or save more data, so you must act in time to avoid losing the stored files.

The System Forces the Equipment to be Repaired

Although this failure usually occurs after a sudden computer shutdown, it is also due to the accumulation of bad blocks in the SSD. You will recognize it because, when you start your PC, an error message will appear, indicating that the file system needs to be repaired.

The Blue Screen Appears Frequently when Starting the PC

The so-called BSOD (Blue Screen of Death, BSOD), or blue screen of death, should be a cause for concern when it starts to appear frequently when booting the PC. Sometimes this problem is solved by backing up the files to another storage unit to format the one used and reinstall the operating system, but if the blue screen continues after formatting, it is best to act soon to avoid the loss of your information.


Although It Is Not a frequent problem, suddenly the SSD begins to restrict access to the files for editing and only allows read mode, so it will have to be replaced as it does not serve to continue saving information.

Recover Dead Ssd

Other Signs are:

  • Running applications often stop working.
  • Errors trying to move files.
  • File access speed has slowed down considerably.
  • The PC freezes or is so slow that it needs to be restarted often during the day.
  • It takes a long time to save or open files.

Is it Possible to Repair a Dead SSD?

If you are looking for how to repair a dead SSD, you will probably find websites that offer you the download of software to fix the damaged blocks, however they are not recommended because, in many cases, they contain malicious viruses or malware.

On the other hand, a damaged storage unit can be partitioned, that is, create different spaces, as if there were more than one hard disk, to perform a light backup of the data. This work is exclusive to a professional in systems, it also does not guarantee that the SSD drive is 100%.

The most advisable thing is to repair the SSD temporarily, in order to extract the stored information and, later, replace it with a new one.

How to Recover Damaged SSD

The following tips will only serve you if the problem with your SSD is minor, but if it is damaged, it is best that you contact specialists such as SalvageData to help you extract your information successfully.

The Actions to Take are:

  • Restart your unit. It sounds simple, but sometimes a connection failure (such as a bad plug) can affect your equipment. So turn off your PC and disconnect the power cable, check the good condition of cables, plugs and reconnect. Turn on your PC, go to the boot settings menu, and make sure it is configured to boot from the SSD. Start Windows and verify that the drive is recognized and its stored files are found.
  • Firmware update. Press Win + X key at the same time and go to device manager in menu. In the Disk Drives section, right-click on the SSD drive and select the Properties -> Details -> Hardware ID -> OK option. Later, run the SSD firmware update tool, follow the instructions that will appear on the screen, which vary depending on the brand of storage unit.
  • Update the SSD drivers. Press Win + X key at the same time and select Device Manager Option. Expand the Drives section, right click on your SSD device and choose Update Driver. Now, follow the instructions that will appear on the screen and once it is done, restart your PC.

How to Recover Data from an SSD

If your SSD has stopped working, you can easily recover your data … as long as the problem is that you have reached the write limit of your memory cells. However, if your storage drive is damaged or “died” before its end of life, you will need expert help to recover your information.

In general, when you have a storage unit or hard disk, it is best to back up your information and make backup copies periodically, so that it can be cloned to an external drive to extract the data that appears in read-only mode.

Now, if your SSD was damaged due to reasons such as an unexpected power surge, a fall or blow to your PC, among other mechanical damages, recovering your information will be the work of experts such as SalvageData.

At we put our experience at your SSD data recovery service to recover data from SSD with 100% effectiveness. Contact us to diagnose your SSD at the phones (855) 901-1073, you can also write to us at address @ salvagedata. com or through our form, we will gladly help you to recover your data successfully. Request a service order or a free diagnosis today on our website.

Back to Top